Goodridge Brake Lines Hoses and Fittings

PLCC

Aircraft quality clamps to support and locate hoses. They can be secured either by rivet or bolt.

Aircraft Quality Stainless Steel Hose End Clip

Light weight, fully machined, all stainless.

Oetiker Clip and Oetiker Pliers

An effective way of securing your hoses - when a more permanent fixture is required. Secure with an Oetiker crimping tool.

Hose Separators

Route your hoses where you want them, out of harms way. Hose separators are manufactured from billet aluminium and anodised to suit your colour scheme. Great for race vehicles, motorcycles and street machines.

Ty Raps and Saddles

Self-extinguishing nylon pull through ties that self lock. An effective and inexpensive method od securing cables, fluid lines, etc. May be used with or without saddle hose base.

PVC Heatshrink

Self extinguishing PVC protective covering, giving protection against corrosion and abrasion. This tough, hard wearing material may be fitted to braided or any other automotive component and shrunk to size by hot air, with a maximum reduction of 35% of original size.

Raychem Heatshrink

Raychem represents the ultimate high performance covering, offering protection from heat, abrasion and chemical attack. Easily shrink to size using hot air.

Reinforced Platic Tube

To suit Motocross and Enduro applications, this hard plastic tubing can be used over your flexible hose and attached to the fork leg and swing arm.

Flameguard

A glass cloth with an aluminium foil surface on one side. Its lightweight construction makes it a very popular heat and fire protector. It is now also available with Aramid Fibre Reinforced cloth and ultimate strength.

Aramid Flameguard

Offering additional heat and flame protection for all high temperature enviroments.

Fireproof Sleeve

A silicone covered sleeve which acts as a fire retardant, an insulator and a chafe protector. Installed by inserting the hose into the sleeve prior to hose fitting assembly. The standard colour is silver, but is also available in orange on request.

Textalu

An insulative fibreglass sleeving with a silicone coating designed to protect components in high temperature areas where the heavier fireproof sleeving is not required. It provides superior insulation to components that must maintain stable temperatures to assure performance efficiency. Its braided construction allows good flexibility in temperatures as low as -40C.

Polythene Spiral Banding

A flexible spiral binding to provide protection to both hose and paintwork.

Overbraid

Certain pre-formed heater and radiator hoses are impossible to replace with pre-braided stainless steel hose. The stainless steel overbraid fitted over the original hose is the ideal way to finish off any first class installation.

Plastic Red Caps and Plugs

Inexpensive plastic caps and plugs for temporary sealing of hose assemblies and protection of threads.

Apex Universal Joints

The universal joints are made to aircraft specifications and are recognised as being the best available for use with gear or steering linkages. The sizes allow fitting either by welding or pinning. The joint is covered with a rubber boot for protection from dirt and retention of grease.

Fuel Caps and Filler Necks

Custom Fuel Filter

Engineered and designed to aircraft standards these Goodridge filters can be assembled to suit all your filtration requirements. The filter is custom designed to optimise weight reduction whilst maintaining pressure rating. An aircraft specification filter insert providing outstanding cleanliness and can be easily cleaned and replaced.

Facet - Bendix Fuel Pump

These pumps are accepted as the standard pump for all competition applications. A very high standard of construction makes these rugged high performance pumps extremely reliable. May be placed in pairs, either parallel or series.

Fuel Shut off Taps

Lightweight and compact tap, allowing full flow or 100% shut-off.

In-line Thermostats

The cooler thermostat is designed to be fitted into the oil lines between the filter and the cooler. This unit prevents the oil passing through the cooler until a temperature of 75 degrees C has been reached, ensuring a quick warm up, and stops over-cooling of the oil. Available with a range of threads or spigots.

Remote Filter Heads

Aluminium cast filter head with 1/2 bsp female ports or with 1/2" Push Fit tails. A sandwich plate is required if the filter is being re-positioned from the original location.

Sandwich Plates and Adaptor Bolts

Aluminium cast sandwich plate used with our remote filter heads, in-line Thermostats and Oil Coolers.

Copper Crush Washers

Sealing washer for use with chrome plated steel, mild steel and stainless fittings.

Alloy Crush Washers

Sealing washer for use with aluminium and stainless fittings.

Stat-O-Seals

The stat-o-seal is the best sealing washer available. It consists of a synthetic rubber 'O' ring mechanically locked ot the I.D of an aluminium crush washer. This provides the advantages of an O ring seal, but with ease of fitting. Stat-o-seals will tolerate temperatures from: -30C to 233C.

Bondd Seals (Dowty)

High quality bonded Dowty sealing washers in a range of sizes

Oil Coolers

An efficient lightweight Oil Cooler is essential for any competition installation and an often needed option on many street vehicles. Our range of high quality alloy coolers are available in both JIC and BSP threads. Only two widths of cooler are stocked, seven other widths are available on request.